The Track Saw Forum  

Go Back   The Track Saw Forum > Members List

Dino Dino is offline

Master Carpenter

Visitor Messages

Showing Visitor Messages 1 to 10 of 21
  1. tomp913
    05-05-2019 04:00 PM
    tomp913
    Dino, I posted a reply yesterday to the latest thread on the Rip Sizer and got a message that it wasn't posting until it had been "reviewed" by a moderator. I see that it hasn't posted as of today, and am wondering if I said something wrong - don't see how - and this is why it hasn't posted. Thanks. tomp913
  2. Wendell Terrell
    04-03-2019 02:41 PM
    Wendell Terrell
    Hi Dino, could you please check your visitor messages? Thanks, Wendell
  3. Wendell Terrell
    04-02-2019 08:00 PM
    Wendell Terrell
    Hi Dino, how are you, well I hope. A quick question, in one of the older videos where you show a story stick made with B2B, you have some flat, round nuts for adjusting the various parts. What do you call those particular nuts? I've been to 4 different hardware stores looking for them, no one has them and everyone looks at me like I've got a lobster growing out of my head when I ask about them! Help!
    Wendell
  4. Wendell Terrell
    12-05-2018 04:06 PM
    Wendell Terrell
    Hello Dino my friend, so good to see you back posting again, missed you. I have a couple of questions: apparently the shop gremlins have stolen my "y" axis stops for my original SRK. Do you by any chance have any available, there are none listed online? If they are no longer produced, could you give me the dimensions so I can remake them? Also, what version of the SRK do I have, my traveler is made of aluminum with 2 pieces of UHMW to adjust both the fit to the ridge and to the arm and there is only a single center groove instead of the 2 on the latest one you offered? Thanks Wendell
  5. Dik Harrison
    07-22-2017 02:34 PM
    Dik Harrison
    Dino, it seems that nobody can respond to your request for new ideas.

    Dik
  6. dvsk
    02-18-2017 01:04 AM
    dvsk
    Hi Dino. I am looking at buying an EZ1 with the SSRK. My panel bit is a 3 1/2 inch bit. I am concerned that the 3 1/2 inch bit is too big to use with the SSRK and I will have to keep using a router table to do it. I would like to switch to the SSRK to route panels. From your experience do you think this is a good idea? Thanks
  7. joebehr
    02-01-2017 03:13 PM
    joebehr
    I'm new to the forum and your products...just got my 36" set and a separate 72" track...what a breeze to work with. I'm starting a full set of cabinet doors and drawer fronts for our kitchen and a pantry system...can't tell you how much better the job is going with the saw tracks and clamps. Thanks for a great product line.
  8. Westleigh Mike
    10-25-2016 03:13 AM
    Westleigh Mike
    Hi Dino,
    I have just joined the forum and wonder how to purchase the ez track in Australia? Would that be through shipping straight from the US or through an Australian distributor?
    Yhanks
  9. Dino
    07-02-2016 02:18 PM
    Dino
    Hi Dik.
    Just wanted to say hello.
    tx
    d
  10. Dik Harrison
    07-02-2016 10:38 AM
    Dik Harrison
    Hi Dino,

    How are you doing. I'm busy here with getting my shop back functional, and trying to finish up the things I'm doing with the house.

About Me

  • About Dino
    Biography
    I like poetry,inventing and PEACE.
    Location
    Edison NJ
    Interests
    None. except inventing new tools
    Occupation
    you know by now.
  • Signature
    ycf dino
    eurekazone.

Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: Yesterday 04:58 PM
  • Join Date: 07-01-2008

Friends

Showing Friends 1 to 6 of 6

All times are GMT -3. The time now is 02:06 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.