The Track Saw Forum  

Go Back   The Track Saw Forum > Search Forums

Showing results 1 to 23 of 23
Search took 0.03 seconds.
Search: Posts Made By: Todd
Forum: Package design advice 11-04-2018, 12:19 PM
Replies: 24
Views: 788
Posted By Todd
I have both the 5007MGA and the 5008MGA for my...

I have both the 5007MGA and the 5008MGA for my table. The 5008MGA is only used when I need the extra depth of cut. I also have a 7 1/4" Makita cordless and a Milwaukee that also work well. For my UEG...
Forum: How-To 10-21-2018, 11:25 PM
Replies: 10
Views: 519
Posted By Todd
Ken, You can slightly countersink a #4 or #5...

Ken,

You can slightly countersink a #4 or #5 screw into one of the troughs in the track. You do not need a large screw because there is not much pressure on the track.

Todd
Forum: How-To 10-21-2018, 02:20 PM
Replies: 10
Views: 519
Posted By Todd
Neil, I did a few sets of stairs at my house...

Neil,

I did a few sets of stairs at my house a few years ago. I replaced the carpet with 1 1/8" solid oak treads. I had to cut the nose off of each tread so that I could run the riser up...
Forum: Rant, Rate, Rave & Review 07-21-2018, 06:25 PM
Replies: 32
Views: 4,242
Posted By Todd
Dino, Great to see you back online. My...

Dino,

Great to see you back online. My thoughts and prayers are with you for a full recovery.

Take care,

Todd
Forum: Rant, Rate, Rave & Review 07-18-2018, 03:38 PM
Replies: 32
Views: 4,242
Posted By Todd
Jim, I finally was able to reach Eurekazone...

Jim,

I finally was able to reach Eurekazone by phone today. I taked to Charles and voiced my concern about customer service. There is a lady that is answering the phone twice a week. I told...
Forum: Rant, Rate, Rave & Review 07-16-2018, 02:36 PM
Replies: 32
Views: 4,242
Posted By Todd
I agree that if something does not change, the...

I agree that if something does not change, the business will suffer. They will have a hard time getting new customers and they will lose old ones. I have been a customer for about 15 years, but...
Forum: Rant, Rate, Rave & Review 07-16-2018, 10:48 AM
Replies: 32
Views: 4,242
Posted By Todd
My attempts to reach Eurekazone continue to fail....

My attempts to reach Eurekazone continue to fail. They do not answer their phone and they will not respond to phone messages or emails. It has become extremely frustrating. Has anybody been intouch...
Forum: Rant, Rate, Rave & Review 07-12-2018, 08:48 PM
Replies: 32
Views: 4,242
Posted By Todd
I am not sure what is going on with Eurekazone,...

I am not sure what is going on with Eurekazone, but they are definitely not answering the phone or returning emails or phone calls. I ordered 2 sets of Smart Pyramid Kits on June 13th and have still...
Forum: Clamping Systems 03-02-2018, 07:05 PM
Replies: 2
Views: 1,740
Posted By Todd
The clamps do swivel. They work great. I have...

The clamps do swivel. They work great. I have both the 3" and 6".
Forum: How-To 02-10-2018, 12:16 PM
Replies: 3
Views: 894
Posted By Todd
Ken, I live in London, Ontario, Canada. The...

Ken,

I live in London, Ontario, Canada. The winters can be cold here. I had the same problem as you in the winter, not wanting to go out to my garage to do woodworking because it was too cold. My...
Forum: Router Guide Systems 01-02-2018, 12:47 AM
Replies: 10
Views: 3,185
Posted By Todd
I too used 3/4 birch plywood for my garage...

I too used 3/4 birch plywood for my garage workshop cabinets. The cabinet boxes, doors and drawer fronts are all birch. The doors are all edge banded. The cabinets are two years old and I have had no...
Forum: Power Benches 12-03-2017, 07:07 PM
Replies: 2
Views: 861
Posted By Todd
Raised Top Kit

I have used the raised top kit on my EZ1 for years. The bridge can stay in place and you can cut a full sheet of 4'x8' plywood. I use it along with my UEG.
Forum: Material Support Systems 11-28-2017, 01:23 PM
Replies: 69
Views: 11,514
Posted By Todd
I will take two sets please. Good to have...

I will take two sets please.

Good to have you back Dino.

Thanks,

Todd
Forum: How-To 01-24-2017, 05:18 PM
Replies: 9
Views: 2,650
Posted By Todd
Grex 23 Gauge Pinner

I own a Grex 23 Gauge Nailer. It works extremely well, but was on the pricey side. It takes up to 2" pins.
Forum: Track System Power Tools and Dust Collection 10-18-2016, 09:10 AM
Replies: 3
Views: 1,561
Posted By Todd
I currently have a full size Makita 7 1/4...

I currently have a full size Makita 7 1/4 cordless attached to an EZ base. It takes two 18v batteries to give you 36v. It has lots of power.
Forum: Track System Power Tools and Dust Collection 04-07-2016, 09:13 AM
Replies: 3
Views: 1,809
Posted By Todd
I have a Triton 3 1/4 HP router set up on my SSRK...

I have a Triton 3 1/4 HP router set up on my SSRK and I have a Mastercraft 3 HP router set up on the old SRK. I have both routers on the plunge bases and both routers work well. The dust collection...
Forum: Track System Power Tools and Dust Collection 03-31-2014, 11:03 AM
Replies: 39
Views: 12,106
Posted By Todd
Best Cordless Saw

I have the Makita LXT (36V) Cordless 7-1/4 Circular Saw. My use has been limited on the EZ track, but when used it has worked great and it has lots of power. For those that reside in Canada, I...
Forum: How-To 01-10-2012, 05:35 PM
Replies: 2
Views: 1,017
Posted By Todd
The required screws to attach the smart base and...

The required screws to attach the smart base and dust port will be included with these items.
Forum: Router Guide Systems 02-21-2011, 12:59 AM
Replies: 11
Views: 3,953
Posted By Todd
John, I recently purchased a Triton Router...

John,

I recently purchased a Triton Router and a sump pump hose worked great for the dust collection port. The dust port opening is a little smaller then the normal 1 1/4" shop vac hose.

Todd
Forum: Woodworking Philosophies 12-01-2010, 11:10 AM
Replies: 104
Views: 15,740
Posted By Todd
Dino, Please advise if you have a conversion...

Dino,

Please advise if you have a conversion kit for the sizer, and the price. I have a cabinet maker set, tracks, etc that I would like to convert over.

Thanks,

Todd
London, Ontario, Canada
Forum: Positioning and Measuring Systems 11-05-2010, 10:36 AM
Replies: 43
Views: 10,607
Posted By Todd
Dino, Can you advise what the price would be...

Dino,

Can you advise what the price would be for the sizer upgrade kit if you already have the tracks and repeaters.

Thanks for your time,

Todd
Forum: Display Case 08-21-2010, 04:17 PM
Replies: 3
Views: 2,085
Posted By Todd
EZ T.V. Cabinet

I do not usually post, so I hope this works properly. This is a T.V. cabinet I recently completed with the help of the EZ system. The sheet goods were cut down by using the track system and my B-300....
Forum: Positioning and Measuring Systems 07-24-2010, 06:59 PM
Replies: 26
Views: 7,411
Posted By Todd
12 seconds

12 seconds
Showing results 1 to 23 of 23

 
Forum Jump

All times are GMT -3. The time now is 10:16 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.