The Track Saw Forum  

Go Back   The Track Saw Forum > Search Forums

Showing results 1 to 16 of 16
Search took 0.01 seconds.
Search: Posts Made By: Bryan Parlor
Forum: Rant, Rate, Rave & Review 05-28-2013, 09:33 AM
Replies: 17
Views: 2,990
Posted By Bryan Parlor
[QUOTE=bigjohn1;31714]I hope this was a mistake...

[QUOTE=bigjohn1;31714]I hope this was a mistake but when I placed an order in for a base at 39.00
UPS shipping came up as 24 and change. Whem with USPS and Dino it was 25% what is this one 51% crazy...
Forum: Track System Power Tools and Dust Collection 02-20-2013, 02:39 PM
Replies: 5
Views: 1,417
Posted By Bryan Parlor
I use this water dust trap for drywall. It...

I use this water dust trap for drywall. It captures most of the sanding dust and very little seems to get through to the shop vac.

http://www.sandkleen.com/products.htm

Bryan
Forum: How-To 05-30-2012, 01:22 PM
Replies: 13
Views: 6,324
Posted By Bryan Parlor
Cement fiber dust

Get a decent dust mask for cutting cement fiber board with a circular saw, paper masks are not recommended for use with silica dust.

http://www.silicosis.com/warnings/index.php.

I score Hardie...
Forum: Woodworking Philosophies 06-16-2011, 09:59 PM
Replies: 16
Views: 8,359
Posted By Bryan Parlor
I voted for my custom PBB but the bridge is my...

I voted for my custom PBB but the bridge is my favorite tool(not on list).

Bryan
Forum: Material Support Systems 06-09-2011, 07:01 PM
Replies: 19
Views: 7,042
Posted By Bryan Parlor
I made a pair of roller clamps using wheels from...

I made a pair of roller clamps using wheels from a old pair of inline skates. The skates use sleeve washers which solve the problem of attaching the roller without binding the rotating wheel.

I...
Forum: Track System Power Tools and Dust Collection 02-21-2011, 10:24 AM
Replies: 12
Views: 4,472
Posted By Bryan Parlor
[QUOTE=jswingchun;11571] Bonus points if you...

[QUOTE=jswingchun;11571]

Bonus points if you can tell what I was making!![/QUOTE

It looks like a baffle for a Thien type dust collector.

http://www.cgallery.com/jpthien/cy.htm

Bryan
Forum: Woodworking Philosophies 02-14-2011, 09:50 PM
Replies: 12
Views: 4,966
Posted By Bryan Parlor
Why not use your existing angle grinder? The two...

Why not use your existing angle grinder? The two handle holes allow it to be mounted on an Smart router kit (SRK) or SSRK with a simple U bracket.
In the attached pictures the nose of the grinder...
Forum: How-To 06-23-2010, 10:01 PM
Replies: 7
Views: 2,662
Posted By Bryan Parlor
Thickness Planning with a Hand Power Planer

Using a hand power planer freehand requires a steady hand if you want a good finish. I can't reliably do it but here is a fool proof way to get precise thickness planning.

I needed to plane off...
Forum: How-To 06-23-2010, 04:47 PM
Replies: 7
Views: 2,662
Posted By Bryan Parlor
Re-surfacing used Lumber

A couple of pictures of re-surfacing some legs for a hall bench using a hand power planer and the EZ system. The legs were originally off an old table.

The workpiece was sitting on the bench...
Forum: Power Benches 03-31-2010, 08:49 PM
Replies: 1
Views: 886
Posted By Bryan Parlor
Hi Gerry, Assuming the B300 is at the limit...

Hi Gerry,

Assuming the B300 is at the limit of its range, it looks like the SME's are fitted too high. Drop them down so that the rail sits flat on the table without a workpiece under it.

Bryan
Forum: Router Guide Systems 03-23-2010, 12:10 PM
Replies: 9
Views: 2,297
Posted By Bryan Parlor
HI Jeff, I use the trap method a lot for...

HI Jeff,

I use the trap method a lot for routing.

Push the work piece against the guide rail (white edge removed) then screw a piece of scrap on each side to trap it. The bridge can then be...
Forum: Track System Power Tools and Dust Collection 02-16-2010, 10:38 PM
Replies: 21
Views: 11,288
Posted By Bryan Parlor
No more pictures but a few tips. I used a...

No more pictures but a few tips.

I used a 2in 90deg ABS pipe fitting for the intake so that the incoming dust is directed towards the container walls. The vac connection is a piece of a shop vac...
Forum: Track System Power Tools and Dust Collection 02-16-2010, 05:48 PM
Replies: 21
Views: 11,288
Posted By Bryan Parlor
Peter, I made a Thien separator and used the...

Peter,

I made a Thien separator and used the SRK to cut the two circles.

I measured that 98% of dust was collected by the cyclone. I used it to pick up 1082 gm of saw dust and found that only...
Forum: Forum 01-29-2010, 02:21 PM
Replies: 2
Views: 1,543
Posted By Bryan Parlor
Thanks for the info Randal hopefully that will...

Thanks for the info Randal hopefully that will fix the problem.

Bryan
Forum: Forum 01-29-2010, 10:57 AM
Replies: 2
Views: 1,543
Posted By Bryan Parlor
Exclamation Crazy Forum Clock

I have noticed for some time that the forum clock keeps changing throughout the day and I wonder why no one else has commented on it.

The welcome screen tells me that I last visited at 2.30 AM...
Forum: Router Guide Systems 01-25-2010, 11:37 AM
Replies: 7
Views: 1,507
Posted By Bryan Parlor
Aligning the bit

My Triton router has a plastic dust shield around the bit - works great but makes it difficult to see to align the bit when using the SRK. It isn't a problem in the upside down mode (router table)...
Showing results 1 to 16 of 16

 
Forum Jump

All times are GMT -3. The time now is 08:44 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.