The Track Saw Forum  

Go Back   The Track Saw Forum > The Track Saw Forum > The Old Wood Stove

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 01-26-2013, 11:44 PM
Jeff Freelove Jeff Freelove is offline
 
Join Date: Aug 2009
Location: Round Rock, Texas
Posts: 147
Default EZ Shop design...decision time

We are building our retirement home (and my shop) in the very near future. I'm lobbying for 600-800 sq ft. with a double garage door and a large electric service.

Is an EZ ONE shop layout much different than a shop with a tablesaw as the primary tool?

My stationary tools include:

Lathe, drill press, 6" jointer, 14" bandsaw, router table, and EZ ONE.

What layout works for y'all?

Last edited by Jeff Freelove; 01-27-2013 at 12:44 AM.
Reply With Quote
  #2  
Old 01-27-2013, 12:55 AM
Dino Dino is online now
Master Carpenter
 
Join Date: Jul 2008
Location: Edison NJ
Posts: 5,096
Default

Quote:
Originally Posted by Jeff Freelove View Post
We are building our retirement home (and my shop) in the very near future. I'm lobbying for 600-800 sq ft. with a double garage door and a large electric service.


Poor Jeff,
After all years in the service you have to lobby for your shop?


Is an EZ ONE shop layout much different than a shop with a tablesaw as the primary tool?

My stationary tools include:

Lathe, drill press, 6" jointer, 14" bandsaw, router table, and EZ ONE.

What layout works for y'all?
Here is the ez-shop.
http://www.more4you.com/Gallery/index.html
__________________
ycf dino
eurekazone.
Reply With Quote
  #3  
Old 01-27-2013, 10:01 AM
Jeff Freelove Jeff Freelove is offline
 
Join Date: Aug 2009
Location: Round Rock, Texas
Posts: 147
Default Heart of the shop

Thanks Dino. The EZ One is the heart of the shop.

I'm thinking the Smart table could be used to breakdown ply or stage it for cabinet carcasses. Position it close to the EZ-1 or put casters on it? Or do you use a rolling lumber storage rack and omit the Smart table altogether?

DC ducts along the side and back walls to make clean up easier. Locate the DC at the overhead door so I don't have to drag it thru the shop to empty it and the Makita lunchbox planer can be used outdoors with a DC hose attached.

I think the compressor should be close to the overhead door too. But still run copper air lines behind the stationary tools and work bench.

Bottomline: What works best in a medium sized (600-800 sf) cabinet shop?
Reply With Quote
  #4  
Old 01-27-2013, 12:29 PM
Burt Burt is offline
Moderator - Cabinet Making
 
Join Date: Jun 2008
Location: Sumter, SC
Posts: 3,682
Default

Jeff,

I've closed my commerical shop and am working on a shop of about 400 square feet for a retirement shop. I stayed away from the garage door and went for a double door setup. In my commerical shop I have a garage door and closing the air holes around it proved to be impossible.

I'm going to use the little smart table that I posted recently in my shop. The top is 21x 36 at its smallest and the extrusions in the top work great for clamping and assembly. I can add the wood strips when I need them and have a table that is about 7' x 3'. I am using this instead of a traditional work bench. I started out with a 5' x 2' setup that extends to about 14 feet but it is to large to mannuver around easily.

My emphasis is on light and portable for the EZ Stuff. The Main power bench will be close to the size of the EZ One but with some different turns.

I"ve just finished a small cross cutter 40" x 16" that expands to a little over 5' long.

Also I have multiple SSRK's. Cabinet Maker's, Ueg's, squares and I think I am down to one RipSizer. I also have a good selection of traditional tools.

I've been working on a router table for months. Somehow I just can't get it right. I think I may be trying to put to much into one table.


Burt
Reply With Quote
  #5  
Old 01-27-2013, 05:32 PM
Glenn Glenn is offline
 
Join Date: Aug 2009
Posts: 107
Default

I have every tool and cabinet (including EZ-1 ) on lockable casters. Thus I can position as needed for a given project
Reply With Quote
  #6  
Old 01-27-2013, 05:55 PM
Dino Dino is online now
Master Carpenter
 
Join Date: Jul 2008
Location: Edison NJ
Posts: 5,096
Default

Quote:
Originally Posted by Glenn View Post
I have every tool and cabinet (including EZ-1 ) on lockable casters. Thus I can position as needed for a given project
Glenn, send me some pictures and info here.
looks like the casters are becoming popular.

tx
__________________
ycf dino
eurekazone.
Reply With Quote
  #7  
Old 01-27-2013, 07:13 PM
Burt Burt is offline
Moderator - Cabinet Making
 
Join Date: Jun 2008
Location: Sumter, SC
Posts: 3,682
Default

Quote:
Originally Posted by Glenn View Post
I have every tool and cabinet (including EZ-1 ) on lockable casters. Thus I can position as needed for a given project
I've done that for years. Being able to move all the stuff in the shop sure makes life easier. You can choose to work by the open door or near the AC unit.


Burt
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -3. The time now is 04:36 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.