The Track Saw Forum  

Go Back   The Track Saw Forum > EurekaZone Forum > EZ Specials

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 12-16-2018, 11:07 AM
Dino Dino is online now
Master Carpenter
 
Join Date: Jul 2008
Location: Edison NJ
Posts: 5,214
Exclamation The EZ Special 4 the ez guys.

Hello Ez guys.
Trying to come up with a Super Special that includes what we mostly need.
Following the forum I noticed the need for extra bases and extra edges.
The same time I like to promote the Pyramids.

WE all know that a good cut requires:
A. good support.
With the EZ pyramids you don't even need wood strips or Foam.
Just make sure that the Pyramid is not in the cut path. Easy? Not even a table.
B. Clean cuts.
With the ez-smart base. to give you the much needed excuse to buy a new saw.
You can tell your wife that you have the free base. I'm sure you can do it.
We can all agree here that no other tool cuts better than EZ's design.
I call it Minus Zero. Now even better with minor design upgrades.
Things that we don't notice in the tool but we can see it in the cut.
C. Safe cuts.
when cutting freehand or using edge guides or straight edges.
Only EZ provides that feature. Many times we don't have to transport and
use guide rails and cutting tables.
Here comes the EZ-Fin for safety and the inserts for clean cuts.
To make the ez Special complete and for all, why not include some new edges?
Yes. The ez edges was a nightmare to design and extrude.
We invested in 4 dies already and many test runs and modifications.
I will not touch them again.

Why stop on the edges? We can include almost everything...
now that we have not one but four free Pyramids?
I'm sure many of us like to have our very own EZ Bridge(s).

I'm thinking of a S.Special that includes the new Pyramids as a free bonus.
A set of (4) with dogs and (4) painters spikes and (4) Non Skid rubber pods.
One Smart base with AC-1, AC-2, One Fin and a Fin Insert.
Antichip Edges.
At 35% OFF. 36"-54" in one piece length.
64"-72's. in two pieces each strip.
we can easily use different size edges to make up any custom length and avoid shipping cost and damages. Delays and other issues.
A small piece ( strip) of any tape will do the job just fine.

I think the above items combined makes a good reason
to take your money and continue our EZ quest for better woodworking.
We know our faults and the let down of our customers in few areas.

To combat the above I will start using a Cell.phone
to provide 24-7 tech and CS support.
To make sure that new tools are getting done faster and without any production and political issues...We started using a 3-D printer
that makes parts and avoid delays and back-ordering etc, etc,...

The same time a NJ shop is in the ez-forever plan.
Time to re-visit some critical areas and start making videos again.
Teach ez woodworking and whatever I can do to make sure that ez
is going to be alive and open for new generations of smart woodworkers.

How much?
$50.00 for the base system with all inserts
Free set of Pyramids.
35% OFF on edges and all items except Power Tools and Guide rails.
I will post here when the special is ON the site.
Shipping via USPS priority.
Timing? We will try our best to ship all orders within a week.
Special Packages with power benches may take longer.

Now...What excuse you need not to make something for your wife...
Please, don't take it on me.
I have to find my own.


Thanks again.
ycf dino
__________________
ycf dino
eurekazone.

Last edited by Dino; 12-16-2018 at 11:51 AM.
Reply With Quote
  #2  
Old 12-16-2018, 03:33 PM
davehodge davehodge is offline
 
Join Date: Sep 2011
Location: Southern Oregon Coast. Brookings Or.
Posts: 18
Default

Dino I hope you make your own videos and not use someone else! You are the reason I went with EZ because you didn’t rehearse or cut out little mistakes, they were real life videos and I also liked your broken English it would make me chuckle a little bit but I could tell your heart was in the right place! You don’t have to be the biggest baddest company out there because you can and should be very proud of what you have done! Please don’t make promises you aren’t sure you can keep, we all know life isn’t perfect and sometimes things are out of our control! If something is isn’t going to happen please let us know on this forum because we will understand and have your back! For me the hey needs to have more accurate measurement system with adjustable hair line curser add it to the cost most of us would appreciate it! Just be you! Best to you and your family, Dave
__________________
daveh
Reply With Quote
  #3  
Old 12-20-2018, 04:24 AM
Dino Dino is online now
Master Carpenter
 
Join Date: Jul 2008
Location: Edison NJ
Posts: 5,214
Default

Quote:
Originally Posted by davehodge View Post
Dino I hope you make your own videos and not use someone else! You are the reason I went with EZ because you didnít rehearse or cut out little mistakes, they were real life videos and I also liked your broken English it would make me chuckle a little bit but I could tell your heart was in the right place! You donít have to be the biggest baddest company out there because you can and should be very proud of what you have done! Please donít make promises you arenít sure you can keep, we all know life isnít perfect and sometimes things are out of our control! If something is isnít going to happen please let us know on this forum because we will understand and have your back! For me the hey needs to have more accurate measurement system with adjustable hair line curser add it to the cost most of us would appreciate it! Just be you! Best to you and your family, Dave
Thanks Dave.
Thanks for all your support and input that we much needed.
thanks for the advice that I never followed until now.
I learned the hard way and I even started to design and make stuff
like there is no other way but the way I can.
For security reasons even if the part or tool is going to be made by others and i different way. Keeping the promises requires to keep your methods.
Lucky to have ez that can do just about anything.
btw, do you ever find a task that you had to drop ez for another tool?
I like your approach and is going to be part ( copied) of ez.
Like Burt's Dik's Joe's and many others.

Enjoy.
__________________
ycf dino
eurekazone.
Reply With Quote
  #4  
Old 12-20-2018, 06:59 PM
davehodge davehodge is offline
 
Join Date: Sep 2011
Location: Southern Oregon Coast. Brookings Or.
Posts: 18
Default

There are times I need to make miter cuts on trim or crown molding I will use my chop saw or I might need a thin rip cut Iíll use my portable table saw only because of setup time with EZ . I build cabinets and furniture and have a shop set up for ripping with adjustable stops at ends and back side and have used the ueg with added wood rip guide to do 8í 45 degree miters off the factory edge with excellent results! I use my dedicated cross cut station to cut to length face frames and all panels. I use a delta unifence to get exact lengths. I reversed my B 300 bridge to pull backwards which snugs my work pieces up against my fence!
__________________
daveh
Reply With Quote
  #5  
Old 12-21-2018, 11:00 AM
Ken Ken is offline
 
Join Date: Sep 2009
Location: West Virginia
Posts: 417
Default

When will this special be available? I could use a saw base, new inserts, and fin to replace the old base on my Hilti. I have also been interested in the Pyramids but would like to get 2 sets to play with.

A few days ago I ordered the UEG to replace my old Ripsizer. The Ripsizer does a fine job but the UEG is smaller, lighter and more maneuverable. I could have just made my own but at the sale price it wasn't worth my time which would be better spent making money or doing a few projects that the wife asked for!

Now as for the Pyramids. I used something very similar on my front deck. They were much larger and made out of concrete. They hold 2X lumber just like the Pyramids plus accept a 4X4 in the middle. I was just curious if the Pyramids were a result of an AhHa moment while building a deck?
Reply With Quote
  #6  
Old 12-21-2018, 02:26 PM
Dino Dino is online now
Master Carpenter
 
Join Date: Jul 2008
Location: Edison NJ
Posts: 5,214
Default

Ken.
An entire table in a very small box.
a table that holds the pieces together to screw.
then we include the spikes for painting.

NEED was the eureka moment
In time they will become one of the best tools.

Cutting in top of the counter top or the floor is easy and smart.
creating any shape and size platform to storage stuff and avoid moisture damages... even screw wood or aluminum to make your powerbench that comes apart is a good feature.

Amazon has a special from PTP, search ez pyramids under workbenches.
Or call the office to get the special that was posted on pre-orders.
whatever is less.

tx
__________________
ycf dino
eurekazone.
Reply With Quote
  #7  
Old 12-22-2018, 02:32 PM
Ken Ken is offline
 
Join Date: Sep 2009
Location: West Virginia
Posts: 417
Default

I found them on Amazon an ordered 2 sets. The shipping was combined so it wasn't bad. These will get plenty of use in some projects that are coming up.
Reply With Quote
  #8  
Old 01-01-2019, 02:29 PM
Dino Dino is online now
Master Carpenter
 
Join Date: Jul 2008
Location: Edison NJ
Posts: 5,214
Thumbs up The EZ Clean Cut.

Happy new year with a clean cut...

https://www.eurekazone.com/ProductDe...Code=EZCC52SME

Capacity and all the good stuff.
When we first intro the antichip protection on both sides of the blade
the reaction of many " green colored" buyers/owners...was:
Who needs this ...... another thing to get lost... and much more.
Later, when they copied some of the features...it was the best thing ever.

The above system is the best low cost entry system
that offers all the good stuff.
Full capacity. 48"
Cleanest cuts. ( Via AC-1s)
Safest cuts ( Thanks to the FIN)
Universal base for right and left saws...that can be used in the tracks. or the UEG...
Two EZ modified toggle clamps that can be used in all ez extrusions...
And one multi use SME ( Straight edge here) extrusion.

All the above at $99.00 .
Happy new year.
__________________
ycf dino
eurekazone.

Last edited by Dino; 01-01-2019 at 02:32 PM.
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -3. The time now is 01:21 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.